![]() ![]() Water test the entire installation by filling up the tub with water up to overflow opening and check for leaks. Tighten up all the slip joint connections. Waste and Overflow Washer Gerber Style Gerber 91-150 Lester Say All ways dry fit your repair and make sure that is the right size and type for your. Attach the cover plate to the overflow elbow using the two cover plate machine screws. Patented Adjustable Self-Retaining Rubber Head Gasket, Patented Pre-Adjustable Linkage, Cast Brass Pop-Up and Shoe Plug, Heavy Duty Highly Polished Faceplate, Extra Long Plunger Stroke, Heavy Duty Cast Red Brass Head, Tee and Shoe, Zinc Plated Coupling Nuts. Insert assembled adjustable nut, threaded rod, and plunger into the overflow elbow until it is all the way inside, and adjust as necessary. Plastic Cable Drain in White Part G150156DY1 Item 182170 Mfr. Attach the adjustable nut to faceplate using the cotter pin cover plate machine screws. Home All Products Plumbing Parts & Supplies Bath Waste & Overflow 24 results for 'Bath Waste & Overflow' Category: Bath Waste & Overflow Brand: Geberit Sort Featured Show List View Geberit TurnControl 24 in. Set the waste tee in place and tighten the slipnut after it has been slipped into the drain line. (Threads of slipnuts should be facing outwards). place a slipnut and a washer on the waste tube and on the overflow tube. ![]() Wipe off any excess putty or silicone with a dry towel. Screw in the shoe strainer through the tub into the shoe elbow, and use pliers to secure shoe strainer into the shoe elbow. (Do not use plumbers putty on marble or plastic surfaces). Place plumbers putty or silicone sealant on underside of shoe strainer. Set the shoe elbow and tube under the tub with a rubber washer between the shoe elbow and the tub. This Trip Lever is easy to install, place the rubber gasket on the overflow elbow. Gerber Faucets - Gerbers product range includes residential vitreous china, commerical plumbing fixtures, electronic faucets, electronic flush valves. This trip lever set includes an overflow elbow, an overflow washer, an overflow drain tube, a waste elbow, a locknut, a wast plug assembly, and an overflow plate with a lever handle. Washers: Washers are used to seal between the tub and the overflow horn and the strainer and the shoe.Wal Rich 1404002 1-1/2" Gerber Style Trip Waste Overflow 17 Gauge, specially designed as a complete assembly that fits all standard tubs. story or even into the waste paper basket with a half-eaten lettuce and tomato sandwich. Trip Lever Over flow plates: Trip Lever Over flow plate Mounts to horn head with 2 bolts. Well, I've got music here which I want Mr. Strainer Covers: Strainers Covers are attached to the strainer some use screws other have tabs that fit into the strainer. Strainers: Strainers are attached to the shoe and are sealed with a washer between the tub and the strainer. Lester Says "Some of the Brand Names are Rapid Fit, Tip Toe Lift & Turn Twist & Pull" Shoes: Shoes are attached to the drain tee and are sealed with a washer between the tub and the shoe. Stopper Gaskets: Stoppers Gaskets are Replaceable rather than replacing the entire stopper. Lester Says "Some of the Brand Names are Rapid Fit, Tip Toe Lift & Turn Twist & Pull" Stoppers: Stoppers are used to plug the drain strainer. Single Hole Over flow plates: Single Hole Over flow plate Mounts to horn head with 1 bolt. You may also like Gerber 41-813 Classics Trip Lever Drain for Roman Tub ARC TrueDEK Classic Drains Geberit 150.156 Turn Control Complete Bath Waste and. ![]() Lester Says " the most important dimention is the diameter of the bucket you can replace a brass bucket with a plastic" Plates: Plate is attached to the overflow horn. Linkage: Linkage is attched to the tub bucket and the trip lever. Overflow Horns: Overflow horn The overflow horn attches the overflow to the drain tee. Lester Says "If you left click your mouse you can download the photo and use your photo software to size to full size to to make sure the part is what you need.īolts Used to attach plate to head of overflow horn Lester Says"In most cases bolts are 1/4 inch x 20 thread"īuckets: Bucket The Bucket is the used with trip lever overflow plates it is attached by linkage to the trip lever.Ĭonversion Plates: Conversion Plates Are used to change from a 2 hole overflow plate to a s ingle hole over flow plate.ĭouble Hole Over flow plates: Double Hole Over flow plate Mounts to horn head with 2 bolts. Lester Say " All ways dry fit your repair and make sure that is the right size and type for your repair" Use photos to ID your replacement parts. Lester Says "If you left click your mouse you can download the photo and use your photo software to size to full size to to make sure the part is what you need. Waste and Overflow Washer Gerber Style Gerber # 91-150 ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |